東原(香港)有限公司
東原(香港)有限公司成立於2002年，並獲得國際知名的意大利品牌樂賽爾 LOXEAL授權為中國和香港區的代理，銷售樂賽爾旗下的優質黏合劑/工業用膠水和密封劑。
辦公地址
香港新界屯門新平街2號
屯門工業中心B座7字樓2室
聯絡資訊
電郵：[email protected]
電話：+852 2792-7838
+852 2792-4228
傳真：+852 2792-4138
Thread sealing
Return to Previous Page
Thread sealing
For: water / gas pipes
Anaerobic thread sealing adhesives seal and lock threaded connections against pressure of gas, air, water, oils, hydrocarbons and many chemicals.
They replace hemp and PTFE tapes and are available in various grades of locking strength with resistance to various chemicals. Certified according to various international standards, e.g. DVGW, NSF, WRAS, KTW, BAM, WATER MARK.
Anaerobic sealant for thread connections allowing easy dismantling of parts. DIN-DVGW approved for gas (Reg. nr. NG 5146AT0263). Upon curing will give an elastic film to replace yarn, P.T.F.E. tapes, and solid gaskets for the sealing of gas, air, water, LPG, oils, hydrocarbons and many chemicals. Easy to dismantle. Shocks and vibrations resistant, it will keep unaffected properties of sealing in the range of temperature from -55°C to +180°C.
Anaerobic adhesive for sealing of metal thread pipe joints. Suitable for gas, LP gas, compressed air, gasoline and oil, industrial fluids, CFC, water and several chemicals. Low friction coefficient will assure easy assembly. Thixotropic property prevents migration from thread of the sealant before or during curing. It replaces P.T.F.E. tape and yarn. Cured product provides elastic film. Shocks and vibrations resistant; unaffected sealing properties in the temperature range from -55 to +150°C. Easy dismantling is assured even after years.
Approvals for natural gas and LP gas in vapour state.
Europe: approved to EN751-1 by DIN-DVGW NG 5146AR0574 from -20°C to +150° C up to 2” pipe size.
Australia: approved by AGA n.5047 up to 5 bar and 2” pipe size.
Anaerobic curing adhesive for sealing of metal thread joints only.
- Approved for Gas (DVGW, DIN-EN 751-1), high pressure gas and GLP (Australian Gas Association - Approval No. 5048) for working pressure up to 20 Bars
- Approved for use with gaseous oxygen up to 10 Bars and +60°C (BAM Ref. N° II-717/2007 E)
- WRAS listed for contact with wholesome (potable) water, approval number 1310513
- Approved for contact with drinking water (GLOBAL MARK, GM-WM-040164-I01-R00)
- NSF registered in cat. P1(n. 141234) as acceptable for use as a sealant in and around food processing area
Very fast curing, high strength anaerobic adhesive for locking threads and retaining od cylindrical components. Suitable for curing on passive metal surfaces, zinc chromated steel and stainless steel without activator. Highly resistant to heat, corrosion, vibrations, water, gases, oils, hydrocarbons, and many chemicals.
Fast curing anaerobic adhesive for metals, with high mechanical resistance, designed to seal and lock threaded joints and cylindrical couplings.
Provides high resistance to temperature, vibration, chemical agents and aging. Highly resistant to unscrewing on yellow brass, nickel-plated and chromed fittings. Approved as threaded joints sealant for gas pipes under EN 751-1 (DIN DVGW nr. NG-5146BQ0134). Suitable for use with hot and cold potable water up to +85°C (WRAS-approved material BS6920:2000). Positively tested by NSF Laboratoires, Michigan, USA, according to ANSI 61 for potable water contact.Keeps the sealing property until the temperature of +200° C for short periods.
Anaerobic adhesive specific for high mechanical strength on yellow brass, to seal threaded joints and to fix cylindrical couplings. It keeps sealing properties up to +250°C. It’s highly resistant to thermal shocks, vibrations, chemical agents and aging. Its high viscosity allows a great handling tolerance.
Fast curing high strength anaerobic adhesive for locking and sealing threads, and retaining of cylindrical parts. It allows larger machining tolerances. Highly resistant to heat, corrosion, vibrations, water, gases, oils, hydrocarbons, and many chemicals.
Approved for gas - Gaz de France.
Anaerobic adhesive for metals, high strength, to lock and seal threaded joints. Approved for use with drinking water according to TZW-DVGW approved for gas-tight threaded joints according to EN 751-1 (DIN DVGW approval no. 5146AR0573-NG). WRAS approved for contact with wholesome (potable) water; Approval N° 1505512. The product is certified (BAM-Berlin) for use as sealant in the presence of gaseous oxygen up to 20 bar at +60°C.Can be used on all metals, both in free or forced matings. Maintains the sealing properties up to +200°C. High resistance to thermal shock, vibration, water, gas, oils, fuels, refrigerant fluids and other chemicals.
Showing all 8 results
