東原(香港)有限公司
東原(香港)有限公司成立於2002年，並獲得國際知名的意大利品牌樂賽爾 LOXEAL授權為中國和香港區的代理，銷售樂賽爾旗下的優質黏合劑/工業用膠水和密封劑。
辦公地址
香港新界屯門新平街2號
屯門工業中心B座7字樓2室
聯絡資訊
電郵：[email protected]
電話：+852 2792-7838
+852 2792-4228
傳真：+852 2792-4138
ENGINEERING ADHESIVES
Products at a glance
High strength anaerobic adhesive for locking and sealing of studs, nuts, bolts and threaded fasteners not requiring dismantling. It can be used on all metals, either in free or forced matings. It provides temperature resistance up to +200°C and high unscrewing strength. Highly resistant to heat, corrosion, vibrations, water, gases, oils, hydrocarbon many chemicals.
Anaerobic curing adhesive for sealing of metal thread joints only.
- Approved for Gas (DVGW, DIN-EN 751-1), high pressure gas and GLP (Australian Gas Association - Approval No. 5048) for working pressure up to 20 Bars
- Approved for use with gaseous oxygen up to 10 Bars and +60°C (BAM Ref. N° II-717/2007 E)
- WRAS listed for contact with wholesome (potable) water, approval number 1310513
- Approved for contact with drinking water (GLOBAL MARK, GM-WM-040164-I01-R00)
- NSF registered in cat. P1(n. 141234) as acceptable for use as a sealant in and around food processing area
Solvent based treatment for bonding of polyolefin (polyethylene, polypropylene), thermoplastic rubbers, EPDM, PTFE, silicones and other difficult to bond materials. Polyolefin Primer is recommended to be used with Loxeal 34 Instant Adhesive.
High strength anaerobic adhesive for metals, highly resistant to oily surfaces. To be used on cylindrical fitting parts, either for slip fitted and for press fitting assemblies. Retaining compound for rotors, gears, bushes, bearings and pin hubs. Highly resistant to temperature, thermal shocks, vibrations, oils and hydrocarbons, refrigerants and many chemicals.
2-component no-mixing fast curing structural adhesive to be used with its specific Loxeal Activator for bondng metals, plastics, ceramics, woods. No-mixing required, apply Adhesive on one part and Activator on the other, assemble and press parts; fixing is achieved within few minutes. It provides high impact resistance, good peeling and tensile strength, best resistance against gasoline, lubricants, water, heat resistant up to 120°C.
Thixotropic permanent plastic sealant for use on threaded and flanged joints. It does not not harden in time and joints can be easily dismounted.
Seals against gas, LPG, water, gasoline, oils. Can be used in combination with preformed gaskets or alone for gap joints less than 0,1 mm. Resistant to vibrations, thermal shocks, keeps sealing properties within a temperature range of –50 / + 120°C. Prevents from surfaces corrosion.
Approved by Volkswagen for use in motor parts assembly (Ref. AKD 454300).
Loxeal 30-55 is a structural acrylic adhesive to be used with its specific Loxeal Activator, designed primarily for bonding metal to metal, ferrite, ceramics and some thermoplastics. This adhesive may be used in a variety of structural bonding applications due to its versatile capabilities. Structural adhesive 30-55 provides high tensile strength while maintaining excellent product flexibility; this results in tough and durable bonds with outstanding impact and peeling resistance. Curing is effected in few minutes at room temperature.
Cleaners and Removers Low odor Low volatility solvent Can detach and remove silicones, MS Polymers and two-part modified epoxy adhesives from many kinds of surfaces Available...
To be used with acrylic adhesives and with anaerobics. Apply the Adhesive on one part and the Activator on the other; assemble parts and wait few minutes to achieve fixing.
News
Hot Posts
RECOGNITIONS
